Williams Ceramic Coat Paint Protection 911

The following provides a rough scheduled plan of some recent work carried out on a Porsche 911 at our Detailing Workshop based at Brighton City Airport.

THE PLAN

Click to enlarge “THE PLAN”

When this Porsche 911 came in we checked the vehicle over for blemishes that we would encounter and noticed that the customer had chosen to wrap the headlights going for the 911 Sport Classic look, with some personal subtle adjustments. Unfortunately, the headlight wrap has not stood the test of time and now looks unsightly.

It’s pretty much impossible to protect the wrap and polish right up to vinyl without compromising either the finish of the existing wrap or the quality of the machine polishing.

The customer took our advice and chose to have the wrap work removed and re-fitted.

The existing stripes were fitted some time ago and had probably experienced some stretching however they were not fitted how we would like so they were measured up to prepare for a new set to be fitted. You can see how out they were in this image we sent off to our friends at  http://www.itsawrapuk.com

2 MEASUREMENTS OF OLD STRIPES-1

Measuring up the old stripes to get the new ones as close as possible, but obviously not wonky this time.

3 MEASURING

So glad we made the suggestion to replace these stripes as the overall finish would have been compromised with the finish we had in mind.

4 OLD STRIPE

In preparation to clean and machine polish the number plates are removed. Why can’t people do things neatly, did they really need that much tape to hold this plate on?

7 STICKER MESSY

Once the bodywork has been prepared (Wash/Tar and Glue removal/ Clay) it’s onto the real work and the main reason this customer has come to us, to remove the swirl marks or “spider-webbing” effect in the paint.

6 SWIRL1

This is a very common problem which is exaggerated in darker paint due to increased reflection. These tiny scratches are created by any form of touching of the vehicle and build up over time. This will undoubtedly have been created through poor washing, drying, polishing, waxing, wiping etc.

5 SWIRL

Even as I write this blog I can show you an example on my desk see below our MAX WAX graphic in standard office light.

20170824_160054

When I lift the torch up it exposes the swirl marks or “spider-web” effect as the light reflects off the scratches on the darker surface. There are scratches on the lighter grey surface but they are not so visible.  This is probably why a good 70% of the machine polishing we carry out in the workshop is to darker vehicles.

20170824_160139

Some of the deeper scratches on the bonnet we believe were created when the stripes were originally fitted as they ran consistent with the length of the stripe.  It looks like when they were preparing the surface to receive the strip with an alcohol wipe they just rubbed whatever road dirt that was present back and forth. These deeper scratches have now been removed with some wet sanding/rotary machine polishing.

13 MACHINE POLISHING

The paint went through a three-stage machine polishing process, using various compounds, graded polishing pads and both the rotary/dual action polishing machines. Naturally to do this work correctly this is not something that should ever be rushed and you are looking at 16-18 hours to get the paint to MAX WAX standard.

14 MACHINE POLISHING 2

Stripping the interior to make its cleaning as effective and simple as possible, basically if it can be removed we will remove it. The interior is a dark and cramped place to work so we can do a better job cleaning the removed items with some light shed upon them.

8 SEAT REMOVE

All leather is cleaned and protected with Williams leather protection and all fabrics are fully shampooed and protected. Any removed interior components are put to one side in a clean environment ready for fitting once the car is nearing completion.

9 SEAT OUT

Following the deep interior cleanse, we are now at the point where we have performed the following broad tasks:

Interior Vacuum / Initial Wash / Decontamination of Paint / 3 Stage Machine Polishing.

We are now ready to get her wet again this is a necessity as unfortunately two days of machine polishing is messy and created dust, some of which will have been wet compound flick (we try to keep this to a minimum) and residue that gets everywhere.

We must be very careful washing as the paint is now how we want it (as near to perfect as possible) really, we want to protect her now! We are torn between protecting at this stage and washing which could ruin our work. It’s a painful, delicate wash to avoid any damage to the paint.

During the pressure washing you can see that the paint is so perfectly smooth and highly polished the water runs off almost immediately. This is obviously completely bare paint no wax or polish is present as we have spirit wiped following the final dual action buffing stage.

15 BEADING WITH NO WAX OR PROTECTION

The arches go through a thorough clean on the initial wash, but it’s nice to gain proper access and get stuck in. We sit on the floor, in the wheel arch with all the correct decontamination products, the hard work is well worth it.

Once this area is properly cleaned we protect everything with the Williams Ceramic Coat (up inside the wheel arch) so that future cleaning of this area is made easier.

10 WHEEL ARCH

With the wheels off we can ensure they are cleaned correctly throughout and carry out tar and glue removal to the dish of the alloy along with clay to remove any embedded contamination. Naturally while they are off we are also able to alcohol wipe and protect the wheels with the Williams Ceramic Coat easily.

11 WHEELS OFF

It’s so rewarding to put these spotless wheels back into a spotless wheel arch that is going to sit on our spotless workshop floor.

12 UP

Following the careful safe wash and drying the 911 is now ready to be alcohol cleansed (the final preparation stage) for application of Williams Ceramic Coating.

The Williams Ceramic Coating is now applied to all exterior surfaces and the results are stunning.

16 PRE CLEAN

The results of our work can be seen below.

The Williams Paint Glass and Fabric Protection has been applied and the car looks stunning. Outside in the sunlight the direct reflection of the sun being crystal clear, this is how paintwork should look.

19 PERFECTION 2

Paul checking his hair in the reflection.

18 CHECKING PERFECTION

Perfectly polished and protected paintwork with no spider-web effects or “swirl marks”.  The freshly fitted stripes and headlight vinyl look spot on too and all together this Porsche 911 is now looking how it should (beautiful)

17 SUN DOT

The shots below are taken after the satin sheet was removed to present the final work to our customer. He sent these shots into us, as you can see he likes his photography and takes a nice photograph.

26

The light reflects so nicely around our workshop it shows the 911 curves off perfectly.

24

No further words required…

23

20

21

The end

Thanks for reading.

The MAX WAX Team